Root
Slub
ground
Views 8654

Stabilization of concrete floors of industrial and economic premises

Обустроенные на грунте бетонные полы промышленных и хозяйственных зданий могут проседать. Состоящие из отдельных бетонных плит покрытия нередко повреждаются в местах швов или перекашиваются в результате избыточных воздействий при эксплуатации. Благодаря геополимерам ремонт и восстановление уровня бетонных полов можно выполнить, не прерывая рабочий цикл предприятия.

Для обустроенных на грунте бетонных полов даже осадка отдельных плит допустима лишь в определенных пределах. При обустройстве таких полов перед монтажом бетонных плит требуется надлежащее выполнение всех подготовительных работ. Если же во время монтажа пола были допущены ошибки или бетонный пол подвергается ненормированному давлению во время эксплуатации, очень скоро помещению потребуется ремонт. Без него просевшие, деформированные и перекошенные бетонные плиты будут создавать препятствия для нормального хода рабочего процесса.

Voids old assets 

Ремонт и укрепление бетонных полов

Для стабилизации, подъема и укрепления бетонных полов применяют метод Floor Lifting. Он позволяет произвести полноценный ремонт бетонного пола в минимальные сроки. При этом отпадает необходимость демонтажа бетонных плит, стеллажей и установленного оборудования. Таким образом, в сравнении с традиционными методами ремонта бетонных полов серьезно экономятся финансы и время.

Особенностью метода Floor Lifting является то, что при инъектировании геополимерных смол нагрузка на бетонные плиты пола является не недостатком, а наоборот преимуществом. В некоторых случаях рекомендуется даже вначале установить в помещении новую технику и оборудование, и лишь потом выполнять цикл работ по подъему и стабилизации бетонных плит пола. При наличии дополнительных нагрузок на бетонный пол, гораздо легче направить усилия, возникающие при инъектированиии геополимерных смол в нижние слои грунта. Это позволяет качественнее уплотнить грунт и укрепить бетонные плиты.

Crack

Как происходит выравнивание бетонного пола

Ремонт бетонного пола по методу Floor Lifting позволяет ввести в эксплуатацию восстановленные участки пола максимально быстро. Простои, которые в других случаях происходят из-за демонтажа и повторной установки бетонных плит, здесь отсутствуют. Таким образом, применение геополимерных смол оказывает минимальное влияние на течение бизнес-процессов заказчика.

Для подъема, стабилизации и выравнивания бетонных плит выполняют цикл геополимерных инъекций под бетон. Делают это через отверстия диаметром 8-12 мм. Составляющие компоненты геополимеров смешиваются в специальных компактных установках прямо во время инъектирования. Практически сразу после попадания в грунт компоненты геополимеров вступают в химическую реакцию и начинают расширяться. Смолы заполняют все пустые пространства под бетоном, вытесняют жидкость из грунта основания в другие слои почвы и расширяются в сторону наиболее ослабленных участков грунта.

Усиление грунта происходит на расстоянии до 500 мм от места введения геополимеров. При этом на данном участке формируется новый слой с увеличенной несущей способностью, воздействие которого позволяет выполнить подъем бетонной плиты. Процесс подъема или выравнивания плиты контролируется в реальном времени с точностью ± 1 мм.

Industry weak soil

Стабилизация пола в холодильных камерах

Особенностью холодильных складских помещений является высокие требования по теплоизоляции, которые касаются, в том числе, теплоизоляции пола. При переоборудовании существующих помещений под холодильную камеру, утеплить пол не всегда просто. Однако в случае применения геополимеров для выравнивания и усиления бетонного пола, косвенным следствием этого действия будет увеличение теплоизоляции помещения со стороны пола.

Это объясняется тем, что при инъектировании для усиления и уплотнения грунта геополимерный материал распространяется под бетоном равномерно и формирует слой герметичный с низкой теплопроводностью. Таким образом, при усилении бетонных полов холодильных камер, геополимеры позволяют дополнительно сэкономить на теплоизоляции пола.

Published: April 13, 2019 by author Groundtek

20 сomments

64x64

Kolesnikov Mihail· Oct. 19, 2020

And if the soil is blocked under the refrigeration cameras?What to do in such a situation?

9 thumb_up

64x64

Aleksandr Sinchenko (inzhener GROUNDTEK) Oct. 19, 2020

The first step should be to determine the depth of the freezing of the base and its condition as a whole.After that, engineers designers make a decision on choosing a way to solve the problem.It is possible to go iteratively - deficing areas and at the same time hesitating his carrying ability, while not stopping the operation of the room, or to start a full-scale long-running construction inside the chambers with excavations and the replacement of the soil to the new and erection of all designs.

64x64

Voronina Nadezhda· Aug. 25, 2020

Good day, whether your geopolymer extinguishes dynamic loads from vibratory machines installed in production?

7 thumb_up

64x64

Aleksandr Sinchenko (inzhener GROUNDTEK) Aug. 25, 2020

Thanks to the cellular structure and built-in elasticity, GroundTek materials have vibration-insulating properties.These advantages have been repeatedly applied in projects around the world at factories or production sites.

64x64

Voronkova Zhanna· May 17, 2019

And if the concrete slab fledged on the construction garbage, as in that case, the geopolymer will work?

7 thumb_up

64x64

Evgenij Novitskij (inzhener GROUNDTEK) May 17, 2019

In this case, it will fill the emptiness, will connect the base and wins under construction.In other words, create a new reliable basis.

64x64

Meshkov Artem· July 23, 2019

How is the required amount of geopolimer needed to fill emptiness under the plates?

10 thumb_up

64x64

Aleksej Karpovich (inzhener GROUNDTEK) July 23, 2019

For calculations, the following data is needed: the carrying capacity of the base, the volume of voids under the floor plate and the load, which must withstand the bearing structures.Considering all these factors, a material is selected with the necessary characteristics for "embedding" into the work of the structures and eliminate the causes of the emergence of structural inconsistencies.

64x64

Bezrukova Natalija· July 19, 2020

And how are you close in the holes through which injections occurs?

5 thumb_up

64x64

Aleksej Karpovich (inzhener GROUNDTEK) July 19, 2020

At the request of the customer.Standard options are either epoxy resin or cement mortar.

64x64

Shapovalova Galina· July 16, 2021

And if the floors in refrigeration chambers already crumble?And the foundation walks ...

7 thumb_up

64x64

Aleksej Karpovich (inzhener GROUNDTEK) July 16, 2021

This situation is very critical.By default, it is necessary to carry out overhaul with dismantling damaged structures.However, if there are requirements for premiting premises, only a competent examination will help find options for a compromise solution and out of difficult situation.

64x64

Korneeva Natalija· Oct. 14, 2020

Is it possible to build so that then do not repair !?)

6 thumb_up

64x64

Evgenij Novitskij (inzhener GROUNDTEK) Oct. 14, 2020

Certainly possible.What is called like a book.But in reality, few people turn out to comply with all the requirements of such construction "so as not to repair."Yes, and it is necessary to exploit the building too "as a book."However, human nature adheres to the rules "So it will come down" or "made and forgotten."

64x64

Chesnokova Alla· Nov. 25, 2019

Good day, what distances are hoses unwound?

2 thumb_up

64x64

Aleksandr Efimchik (inzhener GROUNDTEK) Nov. 25, 2019

The distance from the mobile tract to the injection site can reach 100 meters.This is usually enough in 99% of projects.However, the extension is possible up to 150 meters.

64x64

Savel'eva Anastasija· July 25, 2020

That is, the racks will not interfere with the works and you can not unload them?Is it not very dangerous?

4 thumb_up

64x64

Aleksandr Sinchenko (inzhener GROUNDTEK) July 25, 2020

Yes, you can not unload.In compliance with the safety and technology of production, nothing will happen.There will be no sharp movements.

64x64

Vavilov Vitalij· Oct. 17, 2019

Good day!Do you tell me if the maximum load limit on the floor slab at which the rise is impossible?We in our production installed the machine weighing 140 tons, on the area of 40 m2.The stove of the village is 13 cm, we think to raise into the project level.
Thanks to.

4 thumb_up

64x64

Evgenij Novitskij (inzhener GROUNDTEK) Oct. 17, 2019

Of course the limit is in total in the world and there are limitations for use, however, in your case, you can definitely help.Contact your advice.

64x64

Kazantsev Ruslan· Dec. 26, 2021

And if the floor has already started crumbling?Will the issue of spraying a new coverage solve?

5 thumb_up

64x64

Evgenij Novitskij (inzhener GROUNDTEK) Dec. 26, 2021

Unfortunately no.If structural destruction has begun, only the design can be a reliable solution.It is very important to fix the moment of the start of destruction so as not to bring the element and the processes in which it is involved, to the sad consequences

64x64

Kochetkov Mihail· June 13, 2021

Good afternoon, I saw on your videos how work is done with pulling the tube from the soil while injecting, as I understand it in this way, the pile is formed, and in Russia produce such types of work?

10 thumb_up

64x64

Aleksandr Sinchenko (inzhener GROUNDTEK) June 13, 2021

Yes, thus forming a pile or column.It all depends on the project requirements and ground conditions.In Russia, of course, such works have the place to be

64x64

Zykova Marija· Aug. 22, 2020

Tell me, what I saw in the video rollers on your site, is it really possible ???Raise and align concrete floor with geopolifer!?

5 thumb_up

64x64

Evgenij Novitskij (inzhener GROUNDTEK) Aug. 22, 2020

Yes, in our videos, they are mainly captured by real projects and details of their implementation.

64x64

Petuhova Anzhelika· May 21, 2019

In stock we have problems with concrete floors.Is it possible to order the departure of your specialist to determine the problem and solutions.Where to begin?

4 thumb_up

64x64

Aleksandr Sinchenko (inzhener GROUNDTEK) May 21, 2019

Of course, it is possible to obtain advice and audit object.Contact your contact phone office

64x64

Sveshnikov Boris· May 25, 2019

The process is much faster than the plates replacement?

9 thumb_up

64x64

Aleksej Karpovich (inzhener GROUNDTEK) May 25, 2019

Pumping the plate and alignment on average takes up to 15 minutes of useful time ... you can appreciate yourself that is faster and more convenient ...

64x64

Guschin Ivan· April 16, 2019

And if the floor is even, but when moving the rock or loader just rushes on the joints?Is it suitable for the task of stabilization?

1 thumb_up

64x64

Aleksej Karpovich (inzhener GROUNDTEK) April 16, 2019

Yes, this is the immediate task of stabilization

64x64

Ponomareva Milana· Nov. 26, 2021

Good afternoon.How much time do you need, what would your material hardened?

8 thumb_up

64x64

Aleksandr Efimchik (inzhener GROUNDTEK) Nov. 26, 2021

The material passes different aggregate states.Question in the maximum set of strength?If so, then 90% is recruited for half an hour after the end of the injection, and 100% for 48 hours, respectively

64x64

Ovsjannikova Zhanna· July 25, 2021

What guarantee on your work?

5 thumb_up

64x64

Aleksej Karpovich (inzhener GROUNDTEK) July 25, 2021

Works can be guaranteed up to 60 years

64x64

Galkin Jaroslav· April 24, 2019

What errors in the magnitude of millimeters do you work when lifting the plates?How much I remember the distance of 6 meters go to the tolerance of 8 mm, and how are you?

9 thumb_up

64x64

Aleksandr Efimchik (inzhener GROUNDTEK) April 24, 2019

Our accuracy of work has up to 1 mM error, but usually to save money tolerances include the error +/- 3 mm

64x64

Ivanova Alla· Aug. 28, 2020

And what is meant under stabilization?

9 thumb_up

64x64

Aleksandr Sinchenko (inzhener GROUNDTEK) Aug. 28, 2020

Under stabilization it is understood as the stable position of the floors in space under dynamic (working) load

Post your comment

64x64